Lincoln Aviator: Capacities and Specifications - Plug-In Hybrid Electric Vehicle (PHEV) / Automatic Transmission
Note: Only use MERCON® ULV transmission
fluid for automatic transmissions that require
MERCON® ULV transmission fluid. The use
of any other fluid could cause transmission
damage.
Capacities

1 Approximate dry fill capacity. Actual amount could vary during fluid
changes.
Materials

WARNING: The air conditioning
refrigerant system contains refrigerant
under high pressure. Only qualified
personnel should service the air
conditioning refrigerant system...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
PCM
P0505:00
Idle Control System: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0506:00
Idle Control System - RPM Lower Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0507:00
Idle Control System - RPM Higher Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050A:00
Cold Start Idle Control System Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050B:00
Cold Start Ignition Timing Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050E:00
Cold Start Engine Exhaust Temperature Too Low: No Sub Type Information
GO to Pinpoint Test HU
PCM
P115E:00
Throttle Actuator Control Throttle Body Air Flow Trim At Max Limit: No Sub Type Information
GO to Pinpoint Test HU
PCM
P1548:00
Engine Air Filter Restriction: No Sub Type Information
GO to Pinpoint Test HU
PCM
P2004:00
Intake Manifold Runner Control Stuck Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2005:00
Intake Manifold Runner Control Stuck Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2006:00
Intake Manifold Runner Control Stuck Closed (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2007:00
Intake Manifold Runner Control Stuck Closed (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2008:00
Intake Manifold Runner Control Circuit/Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2011:00
Intake Manifold Runner Control Circuit/Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2014:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2015:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 1): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2016:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2017:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2019:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2020:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 2): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2021:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2022:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
Global Customer Symptom Code (GCSC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Initialization
Disconnect the battery or remove the RGTM fuse(s).
Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
NOTE:
Remove the battery power from the RGTM for 20 seconds before entering initialization mode...
Categories
Each door has a backup power system which
allows the door to function if your vehicle
has no power. The system has a limited
number of operations before the power is
depleted and turns off. When the system
turns off, the door remains open and
unlatched and does not close.
If your vehicle has no power and the backup
power system is turned off, you can close
and secure your vehicle by manually
resetting each door latch using a key in the
position shown.
read more