Lincoln Aviator: Body and Paint / Paint - General Information
Special Tool(s) /
General Equipment
Resistance Spotwelding Equipment
8 mm Drill Bit
MIG/MAG Welding Equipment
Spot Weld Drill Bit
Locking Pliers
Materials
Name
Specification
Flexible Foam Repair3M™ 08463, LORD Fusor® 121
-
Removal
WARNING:
Electric vehicles damaged by a crash may have compromised
high voltage safety systems and present a potential high voltage
electrical shock hazard...
Materials
Name
Specification
Motorcraft® Acid NeutralizerZC-1-A
-
Motorcraft® Alkaline NeutralizerZC-2-A
-
Repair
NOTE:
Refinishing - Environmental Damage
WARNING:
Before beginning any service procedure in this
manual, refer to health and safety warnings in section 100-00 General
Information...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
PCM
P0505:00
Idle Control System: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0506:00
Idle Control System - RPM Lower Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P0507:00
Idle Control System - RPM Higher Than Expected: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050A:00
Cold Start Idle Control System Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050B:00
Cold Start Ignition Timing Performance: No Sub Type Information
GO to Pinpoint Test HU
PCM
P050E:00
Cold Start Engine Exhaust Temperature Too Low: No Sub Type Information
GO to Pinpoint Test HU
PCM
P115E:00
Throttle Actuator Control Throttle Body Air Flow Trim At Max Limit: No Sub Type Information
GO to Pinpoint Test HU
PCM
P1548:00
Engine Air Filter Restriction: No Sub Type Information
GO to Pinpoint Test HU
PCM
P2004:00
Intake Manifold Runner Control Stuck Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2005:00
Intake Manifold Runner Control Stuck Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2006:00
Intake Manifold Runner Control Stuck Closed (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2007:00
Intake Manifold Runner Control Stuck Closed (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2008:00
Intake Manifold Runner Control Circuit/Open (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2011:00
Intake Manifold Runner Control Circuit/Open (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2014:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2015:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 1): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2016:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2017:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 1): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2019:00
Intake Manifold Runner Position Sensor/Switch Circuit (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2020:00
Intake Manifold Runner Position
Sensor/Switch Circuit Range/Performance (Bank 2): No Sub Type
Information
GO to Pinpoint Test HU
PCM
P2021:00
Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
PCM
P2022:00
Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 2): No Sub Type Information
GO to Pinpoint Test HU
Global Customer Symptom Code (GCSC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
System Operation
Lane Keeping Alert and Lane Keeping Aid
Item
Description
1
Lane Keeping System Switch
2
IPMA
3
GWM
4
Camera Windshield Defrost Heater
5
RCM
6
SCCM
7
PCM
8
IPC
9
TRM
10
BCM
11
PSCM
12
with active cruise control
13
CCM
14
Windshield
Network Message Chart
Module Network Input Messages - IPMA
Broadcast Message
Originating Module
Message Purpose
Ambient air temperature filtered
PCM
Used to control the camera windshield defrost heater operation...