Lincoln Aviator: Wipers and Washers / Windshield Washers

Pull the lever toward you to
operate the windshield washers.
When you release the lever, the wipers
operate for a short time. When activated, a
courtesy wipe occurs a short time after the
wipers stop to clear any remaining washer
fluid.
Note: You can switch courtesy wipe on or
off in the touchscreen.
Note: Do not operate the washers when the
washer reservoir is empty. This could cause
the washer pump to overheat.
Front Camera Washer (If Equipped)
Operating the windshield washer also turns
on the front camera washer.
Windshield Wipers - Vehicles With: Heated Wiper Blades
Heated Wiper Blade
The heated wiper blades turn on in low
temperature when the windshield wipers are
active or defrost is on...
Rear Window Wiper
Intermittent wipe.
Continuous wipe.
Rear window wiper off.
Depending on your vehicle, when you switch
on the front wipers and move the gearshift
lever to reverse (R), the rear intermittent wipe
may turn on...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
GSM
P0562:00
System Voltage Low: No Sub Type Information
GO to Pinpoint Test B
GSM
P0563:00
System Voltage High: No Sub Type Information
GO to Pinpoint Test C
GSM
P0605:00
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information
GO to Pinpoint Test L
GSM
P0606:00
Control Module Processor: No Sub Type Information
GO to Pinpoint Test L
GSM
P0607:00
Control Module Performance: No Sub Type Information
GO to Pinpoint Test L
GSM
P06B8:00
Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information
GO to Pinpoint Test L
GSM
P07EC:00
Transmission Range Multi-Function Select Circuit: No Sub Type Information
GO to Pinpoint Test J
GSM
P07ED:00
Transmission Range Multi-Function Select Circuit Stuck: No Sub Type Information
GO to Pinpoint Test J
GSM
P0814:00
Transmission Range Display Circuit: No Sub Type Information
GO to Pinpoint Test I
GSM
P164E:00
Internal Control Module Transmission Range Select Performance: No Sub Type Information
GO to Pinpoint Test L
GSM
P166B:00
Drivers Door Status Correlation: No Sub Type Information
GO to Pinpoint Test H
GSM
U0100:00
Lost Communication With ECM/PCM "A": No Sub Type Information
GO to Pinpoint Test G
GSM
U0100:87
Lost Communication With ECM/PCM "A": Missing Message
GO to Pinpoint Test G
GSM
U0121:00
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information
GO to Pinpoint Test F
GSM
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test E
GSM
U0155:00
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information
GO to Pinpoint Test D
GSM
U0203:00
Lost Communication With Door Control Module "E": No Sub Type Information
GO to Pinpoint Test H
GSM
U0301:00
Software Incompatibility with ECM/PCM: No Sub Type Available
GO to Pinpoint Test M
GSM
U0401:00
Invalid Data Received from ECM/PCM A: No Sub Type Information
GO to Pinpoint Test N
GSM
U0422:00
Invalid Data Received From Body Control Module: No Sub Type Information
GO to Pinpoint Test N
GSM
U0504:00
Invalid Data Received From Door Control Module "E": No Sub Type Information
GO to Pinpoint Test H
GSM
U1011:00
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information
GO to Pinpoint Test O
GSM
U101F:00
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information
GO to Pinpoint Test O
Global Customer Symptom Code (GCSC) Chart
Global Customer Symptom Code Chart
Customer Symptom
Action
Start/Run/Move > Moving > Paddle Shift > Inoperative
GO to Pinpoint Test K
Start/Run/Move > Moving > Gear Selector > Return to Park
GO to Pinpoint Test Q
Start/Run/Move > Moving > Gear Selector > Return to Park
GO to Pinpoint Test R
Start/Run/Move > Moving > Engagement Quality > Park
GO to Pinpoint Test P
Start/Run/Move > Moving > Engagement Quality > Park
GO to Pinpoint Test S
Start/Run/Move > Moving > Gear Selector > Progressive Range Selection
GO to Pinpoint Test A
Pinpoint Tests
PINPOINT TEST A : PROGRESSIVE RANGE SELECTION DOES NOT OPERATE CORRECTLY
Refer to Wiring Diagrams Cell 30 for schematic and connector information...
Removal
Remove the overhead console.
Refer to: Overhead Console (501-12 Instrument Panel and Console, Removal and Installation).
Remove the intrusion sensor.
Release the tab on the LH outer sensor.
Release the tab on the center sensor...