Lincoln Aviator: Adaptive Cruise Control / Adjusting the Set Speed Tolerance
You can set a permanent speed tolerance
that is above or below the detected speed
limit.
Use the touchscreen to select the following:
- Select Settings.
- Select Driver Assist.
- Select Cruise Control.
- Select Tolerance.
- Use + and - to set the tolerance.
Note: You cannot set the tolerance more
than 20 mph (30 km/h) above or below the
recognized speed.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention...
Adaptive Cruise Control – Information Messages - Vehicles With: Adaptive
Cruise Control With Lane Centering
Note: Depending on your vehicle options
and instrument cluster type, not all messages
display or are available...
Other information:
Special Tool(s) /
General Equipment
100-001
(T50T-100-A)
Slide Hammer
100-002
(TOOL-4201-C)
Holding Fixture with Dial Indicator Gauge
205-1018Installation Tube
307-003
(T57L-500-B)
Holding Fixture, Transmission
307-091Handle, Torque ConverterTKIT-2009TC-F
307-309Remover, Torque Converter SealTKIT-1994-FMH/FLMHTKIT-1994-LMH/MHTKIT-1994-FH
307-346
(T97T-7902-A)
Retainer, Torque ConverterTKIT-1998-LM (NavigatoR)TKIT-1997-F/FLM/LT
307-549Installer, Shift Shaft Fluid SealTKIT-2005D1-F1
307-5842-6 Spring CompressorTKIT-2006UF-FLMTKIT-2006UF-ROW
307-589Overdrive clutch and balance piston service setTKIT-2006UF-FLMTKIT-2006UF-ROW
307-651Bracket, Pump Remover/Installer
307-651-02Lift fixture adapter for 307-651
307-661Gauge, End PlayTKIT-2009C-FTKIT-2009C-ROW
307-661-01Spacers/Plate, Clearance Gage
307-662Gauge, Clutch Pack EndplayTKIT-2009C-FTKIT-2009C-ROW
307-691Tester, Torque Convertor Leak
307-732Tool Kit, Torque Converter Flusher
307-732-02Adapter for 307-732 Converter flushing Mandrel
307-736Installer, Pump Drive Gear Bearing
307-737Press Tool, Oil Pump Drive Idler Gear
307-741Spring Compressor, F Clutch
307-743Remover, Pump Drive Gear
307-746Remover, Transmission Wiring Harness Connector
307-780Converter Seal installer
307-782Installer, Output Shaft Seal
307-783Installer, Roll Pin
307-784One way clutch alignment tool
307-785Clutch spring compressor
307-786F7 Seal Installer/Sizer Input Shaft
307-787F8 Seal Installer/Sizer Input Shaft
307-790Endplay Check Gauge
307-796F2 Seal Guide, Installer & Sizer
307-797Installer, Alignment Studs (3) & Alignment Pin (All 10R)
307-803F1 Seal Guide, Installer & Sizer
307-804F9 Seal Guide, Installer & Sizer
Rubber Mallet
Hydraulic Press
Punch
Wooden Block
Magnet
Materials
Name
Specification
Motorcraft® MERCON® ULV Automatic Transmission FluidXT-12-QULV
WSS-M2C949-A, MERCON® ULV
All vehicles
Transmission overhaul includes the following:
Complete disassembly of the transmission
Cleaning and inspecting of all components
Replacement of all seals, gaskets, and one time use components...
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the RH loadspace trim panel.
Refer to: Loadspace Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
Disconnect the electrical connector, remove the retainers and the rear air distribution door actuator...