Lincoln Aviator: Locking and Unlocking / Illuminated Entry
The interior lamps and some exterior lamps
illuminate when you unlock the doors with
the remote control.
The illuminated entry system turns off the
lights if:
- The ignition is on.
- You press the remote control lock button.
- After 25 seconds of illumination.
The lights do not turn off if:
- You turn them on with the lamp control.
- Any door is open.
Illuminated Exit
The interior lamps and some exterior lamps
illuminate when all doors are closed and you
switch the ignition off.
The lamps turn off if all the doors remain
closed and:
- 25 seconds have elapsed.
- You press the push button ignition
switch.
Autolock locks all the doors when:
All doors are closed.
The ignition is on.
You shift into any gear putting your
vehicle in motion.
Your vehicle reaches a speed greater
than 12 mph (20 km/h)...
If you leave the courtesy lamps, interior
lamps or headlamps on, the battery saver
shuts them off 10 minutes after you switch
the ignition off.
Battery Saver for Intelligent Access Keys
If you leave the ignition switched on, it shuts
off when it detects a certain amount of
battery drain, or after 45 minutes...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B130F:12
Run Accessory Control: Circuit Short To Battery
GO to Pinpoint Test A
BCM
B130F:14
Run Accessory Control: Circuit Short To Ground or Open
GO to Pinpoint Test A
BCM
B130F:14
Run Accessory Control: Circuit Short To Ground or Open
GO to Pinpoint Test D
SCCM
B10AD:02
Rain Sensor: General Signal Failure
GO to Pinpoint Test F
SCCM
B10AD:08
Rain Sensor: Bus Signal / Message Failure
GO to Pinpoint Test F
SCCM
B10AD:49
Rain Sensor:Internal Electronic Failure
GO to Pinpoint Test Q
SCCM
B10AD:55
:Rain Sensor:Not Configured
GO to Pinpoint Test P
SCCM
B1131:02
Wiper motor module: General Signal Failure
GO to Pinpoint Test A
SCCM
B1131:02
Wiper Motor Module: General Signal Failure
GO to Pinpoint Test D
SCCM
B1131:08
Wiper motor module: Bus Signal / Message Failure
GO to Pinpoint Test B
SCCM
B1131:11
Wiper motor module: Circuit Short to Ground
GO to Pinpoint Test B
SCCM
B1131:49
Wiper Motor Module:Internal Electronic Failure
GO to Pinpoint Test R
SCCM
B1131:55
:Wiper Motor Module: Not Configured
GO to Pinpoint Test P
SCCM
B124E:11
Wiper Stalk Switch Pack: Circuit Short To Ground
GO to Pinpoint Test V
SCCM
B124E:13
Wiper Stalk Switch Pack: Circuit Open
GO to Pinpoint Test V
SCCM
B124E:55
Wiper Stalk Switch: Not Configured
GO to Pinpoint Test V
SCCM
B124E:96
Wiper Stalk Switch Pack: Component Internal Failure
GO to Pinpoint Test V
SCCM
B124E:9E
Wiper Stalk Switch Pack: Stuck On
GO to Pinpoint Test V
Symptom Chart
Symptom Chart: Wiper and Washer
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Removal
NOTE:
Removal steps in this procedure may contain installation details.
NOTE:
This procedure is for the sliding glass panel only.
Place the roof opening panel shield to the fully OPEN position.
On both sides...