Lincoln Aviator: Locking and Unlocking / Battery Saver
If you leave the courtesy lamps, interior
lamps or headlamps on, the battery saver
shuts them off 10 minutes after you switch
the ignition off.
Battery Saver for Intelligent Access Keys
If you leave the ignition switched on, it shuts
off when it detects a certain amount of
battery drain, or after 45 minutes.
The interior lamps and some exterior lamps
illuminate when you unlock the doors with
the remote control.
The illuminated entry system turns off the
lights if:
The ignition is on...
From Inside Your Vehicle
With the transmission in park
(P),
press the button on the instrument
panel.
With the Remote Control
Press twice within three seconds
to open the luggage compartment...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B11D9:16
Vehicle Battery:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
B11D9:17
Vehicle Battery:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U0100:87
Lost Communication With ECM/PCM "A":Missing Message
GO to Pinpoint Test A
BCM
U0121:87
Lost Communication With Anti-Lock Brake System (ABS) Control Module:Missing Message
GO to Pinpoint Test B
BCM
U0131:87
Lost Communication With Power Steering Control Module:Missing Message
GO to Pinpoint Test C
BCM
U0151:87
Lost Communication With Restraints Control Module:Missing Message
GO to Pinpoint Test D
BCM
U0155:87
Lost Communication With Instrument Panel Cluster (IPC) Control Module:Missing Message
GO to Pinpoint Test E
BCM
U0166:87
Lost Communication With Auxiliary Heater Control Module:Missing Message
GO to Pinpoint Test F
BCM
U0184:87
Lost Communication With Radio:Missing Message
GO to Pinpoint Test G
BCM
U0198:87
Lost Communication With Telematic Control Module: Missing Message
GO to Pinpoint Test H
BCM
U0199:87
Lost Communication With "Door Control Module A":Missing Message
GO to Pinpoint Test I
BCM
U019B:87
Lost Communication With Battery Charger Control Module:Missing Message
GO to Pinpoint Test J
BCM
U0200:87
Lost Communication With "Door Control Module B":Missing Message
GO to Pinpoint Test K
BCM
U0208:87
Lost Communication With "Seat Control Module A":Missing Message
GO to Pinpoint Test L
BCM
U0212:87
Lost Communication With Steering Column Control Module:Missing Message
GO to Pinpoint Test M
BCM
U0230:87
Lost Communication With Rear Gate Module:Missing Message
GO to Pinpoint Test N
BCM
U0232:87
Lost Communication With Side Obstacle Detection Control Module "A":Missing Message
GO to Pinpoint Test O
BCM
U0233:87
Lost Communication With Side Obstacle Detection Control Module "B":Missing Message
GO to Pinpoint Test P
BCM
U023A:87
Lost Communication With Image Processing Control Module A:Missing Message
GO to Pinpoint Test Q
BCM
U0252:87
Lost Communication With Lighting Control Module-Rear "B":Missing Message
GO to Pinpoint Test R
BCM
U0253:87
Lost Communication With Accessory Protocol Interface Module:Missing Message
GO to Pinpoint Test S
BCM
U0256:87
Lost Communication With Front Controls Interface Module "A":Missing Message
GO to Pinpoint Test T
BCM
U0293:87
Lost Communication With Hybrid/EV Powertrain Control Module "A":Missing Message
GO to Pinpoint Test U
BCM
U1000:00
Solid State Driver Protection Active:Driver Disabled: No Sub Type Information
GO to Pinpoint Test V
BCM
U2005:85
Vehicle Speed:Signal Above Allowable Range
GO to Pinpoint Test W
BCM
U2100:00
Initial Configuration Not Complete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2101:00
Control Module Configuration Inomplete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2200:00
Control Module Configuration Memory Corrupt:No Sub Type Information
GO to Pinpoint Test X
BCM
U3000:49
Control Module:Internal Electronic Failure
GO to Pinpoint Test AA
BCM
U3006:16
Control Module Input Power “A”:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3006:17
Control Module Input Power “A”:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Y
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Z
BCM
U3007:16
Control Module Input Power "B":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3007:17
Control Module Input Power "B":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3013:16
Control Module Input Power "C":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3013:17
Control Module Input Power "C":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3014:16
Control Module Input Power "D":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3014:17
Control Module Input Power "D":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
Symptom Chart
Symptom Chart: Multifunction Electronic Modules
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Materials
Name
Specification
Motorcraft® SAE 75W-140 Synthetic Rear Axle LubricantXY-75W140-QL
WSL-M2C192-A
Removal
With the vehicle in NEUTRAL, position it on a hoist.
Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation)...