Lincoln Aviator: Charging the High Voltage Battery - Plug-In Hybrid Electric Vehicle (PHEV) / MOVING AND STORAGE INSTRUCTIONS
Make sure that you completely wrap the
dual-voltage charging cord after charging.
When complete, replace the dual-voltage
charging cord in the luggage compartment.
Note: Do not hold the dual-voltage charging
cord by the flexible power cable.
Note: Store the dual-voltage charging cord
in a clean, dry place between the
temperature of -39.9–157.9°F (-40–70°C).
Use
a three-prong AC outlet that is properly
grounded, 15-20 amps or greater, and in
good condition. Use a dedicated line. You
cannot have other appliances connected to
the same circuit...
Other information:
E..
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B00A0:11
Occupant Classification System: Circuit Short to Ground
GO to Pinpoint Test BN
BCM
B00A0:12
Occupant Classification System: Circuit Short to Battery
GO to Pinpoint Test BN
BCM
B1123:11
Restraints Ignition Relay: Circuit Short to Ground
GO to Pinpoint Test BN
BCM
B1123:12
Restraints Ignition Relay: Circuit Short to Battery
GO to Pinpoint Test BN
BCM
B11D8:01
Restraint Event Notification: General Electrical Failure
GO to Pinpoint Test U
DCME
B1262:92
Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation
GO to Pinpoint Test AX
DCMF
B1262:92
Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation
GO to Pinpoint Test AX
DCMG
B1262:92
Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation
GO to Pinpoint Test AY
DCMH
B1262:92
Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation
GO to Pinpoint Test AY
FCIM
B00D5:01
Restraint System Passenger Disable Indicator: General Electrical Failure
GO to Pinpoint Test R
FCIM
B1202:01
Restraint System Passenger Enable Indicator: General Electrical Failure
GO to Pinpoint Test V
OCSM
B0061:11
Passenger Seatbelt Tension Sensor: Circuit Short to Ground
GO to Pinpoint Test BC
OCSM
B0061:12
Passenger Seatbelt Tension Sensor: Circuit Short to Battery
GO to Pinpoint Test BC
OCSM
B0061:13
Passenger Seatbelt Tension Sensor: Circuit Open
GO to Pinpoint Test BC
OCSM
B0061:64
Passenger Seatbelt Tension Sensor: Signal Plausibility Failure
GO to Pinpoint Test BC
OCSM
B00A0:62
Occupant Classification System: Signal Compare Failure
GO to Pinpoint Test BD
OCSM
B00C0:11
Passenger Seat Occupant Classification Sensor "A": Circuit Short To Ground
GO to Pinpoint Test BE
OCSM
B00C0:12
Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery
GO to Pinpoint Test BE
OCSM
B00C0:16
Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold
GO to Pinpoint Test BE
OCSM
B00C0:49
Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure
GO to Pinpoint Test BE
OCSM
B00C0:7B
Passenger Seat Occupant Classification Sensor "A": Low Fluid Level
GO to Pinpoint Test BE
OCSM
B00C2:11
Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground
GO to Pinpoint Test BF
OCSM
B00C2:12
Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery
GO to Pinpoint Test BF
OCSM
B1193:00
Crash Event Storage Full and Locked: No Sub Type Information
GO to Pinpoint Test BG
OCSM
U0100:00
Lost Communication with ECM/PCM “A”: No Sub Type Information
GO to Pinpoint Test BH
OCSM
U0151:00
Lost Communication with Restraints Control Module: No Sub Type Information
GO to Pinpoint Test BI
OCSM
U024C:00
Lost Communication with Seat Control Module "H": No Sub Type Information
GO to Pinpoint Test BJ
OCSM
U0401:00
Invalid Data Received from ECM/PCM A: No Sub Type Information
GO to Pinpoint Test BK
OCSM
U3000:41
Control Module: General Checksum Failure
GO to Pinpoint Test BL
OCSM
U3000:42
Control Module: General Memory Failure
GO to Pinpoint Test BL
OCSM
U3000:46
Control Module: Special Memory Failure
GO to Pinpoint Test BL
OCSM
U3000:54
Control Module: Missing Calibration
GO to Pinpoint Test BM
OCSM
U3003:16
Battery Voltage: Circuit Voltage Below Threshold
GO to Pinpoint Test BB
OCSM
U3003:17
Battery Voltage: Circuit Voltage Above Threshold
GO to Pinpoint Test BB
RCM
B0001:11
Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground
GO to Pinpoint Test A
RCM
B0001:12
Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery
GO to Pinpoint Test A
RCM
B0001:13
Driver Frontal Stage 1 Deployment Control: Circuit Open
GO to Pinpoint Test A
RCM
B0001:1A
Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test A
RCM
B0001:2B
Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0001:4A
Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0002:11
Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground
GO to Pinpoint Test B
RCM
B0002:12
Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery
GO to Pinpoint Test B
RCM
B0002:13
Driver Frontal Stage 2 Deployment Control: Circuit Open
GO to Pinpoint Test B
RCM
B0002:1A
Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test B
RCM
B0002:2B
Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0002:4A
Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0004:11
Driver Knee Bolster Deployment Control: Circuit Short to Ground
GO to Pinpoint Test C
RCM
B0004:12
Driver Knee Bolster Deployment Control: Circuit Short to Battery
GO to Pinpoint Test C
RCM
B0004:13
Driver Knee Bolster Deployment Control: Circuit Open
GO to Pinpoint Test C
RCM
B0004:1A
Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test C
RCM
B0004:2B
Driver Knee Bolster Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0004:4A
Driver Knee Bolster Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0010:11
Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground
GO to Pinpoint Test D
RCM
B0010:12
Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery
GO to Pinpoint Test D
RCM
B0010:13
Passenger Frontal Stage 1 Deployment Control: Circuit Open
GO to Pinpoint Test D
RCM
B0010:1A
Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test D
RCM
B0010:2B
Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0010:4A
Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0011:11
Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground
GO to Pinpoint Test E
RCM
B0011:12
Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery
GO to Pinpoint Test E
RCM
B0011:13
Passenger Frontal Stage 2 Deployment Control: Circuit Open
GO to Pinpoint Test E
RCM
B0011:1A
Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test E
RCM
B0011:2B
Passenger Frontal Stage 2 Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B0011:4A
Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0013:11
Passenger Knee Bolster Deployment Control: Circuit Short to Ground
GO to Pinpoint Test F
RCM
B0013:12
Passenger Knee Bolster Deployment Control: Circuit Short to Battery
GO to Pinpoint Test F
RCM
B0013:13
Passenger Knee Bolster Deployment Control: Circuit Open
GO to Pinpoint Test F
RCM
B0013:1A
Passenger Knee Bolster Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test F
RCM
B0013:2B
Passenger Knee Bolster Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B0013:4A
Passenger Knee Bolster Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0050:11
Driver Seatbelt Sensor: Circuit Short to Ground
GO to Pinpoint Test G
RCM
B0050:12
Driver Seatbelt Sensor: Circuit Short to Battery
GO to Pinpoint Test G
RCM
B0050:13
Driver Seatbelt Sensor: Circuit Open
GO to Pinpoint Test G
RCM
B0050:1D
Driver Seatbelt Sensor: Circuit Current Out of Range
GO to Pinpoint Test G
RCM
B0050:2B
Driver Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B0050:4A
Driver Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0052:11
Passenger Seatbelt Sensor: Circuit Short to Ground
GO to Pinpoint Test H
RCM
B0052:12
Passenger Seatbelt Sensor: Circuit Short to Battery
GO to Pinpoint Test H
RCM
B0052:13
Passenger Seatbelt Sensor: Circuit Open
GO to Pinpoint Test H
RCM
B0052:1D
Passenger Seatbelt Sensor: Circuit Current Out of Range
GO to Pinpoint Test H
RCM
B0052:2B
Passenger Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B0052:4A
Passenger Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0054:11
Second Row Center Seatbelt Sensor: Circuit Short To Ground
GO to Pinpoint Test I
RCM
B0054:12
Second Row Center Seatbelt Sensor: Circuit Short To Battery
GO to Pinpoint Test I
RCM
B0054:13
Second Row Center Seatbelt Sensor: Circuit Open
GO to Pinpoint Test I
RCM
B0054:1D
Second Row Center Seatbelt Sensor: Circuit Current Out Of Range
GO to Pinpoint Test I
RCM
B0054:2B
Second Row Center Seatbelt Sensor: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0054:4A
Second Row Center Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0070:11
Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground
GO to Pinpoint Test J
RCM
B0070:12
Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery
GO to Pinpoint Test J
RCM
B0070:13
Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open
GO to Pinpoint Test J
RCM
B0070:1A
Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test J
RCM
B0070:2B
Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0070:4A
Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0072:11
Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground
GO to Pinpoint Test K
RCM
B0072:12
Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery
GO to Pinpoint Test K
RCM
B0072:13
Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open
GO to Pinpoint Test K
RCM
B0072:1A
Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test K
RCM
B0072:2B
Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0072:4A
Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B007E:11
Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground
GO to Pinpoint Test L
RCM
B007E:12
Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery
GO to Pinpoint Test L
RCM
B007E:13
Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open
GO to Pinpoint Test L
RCM
B007E:1A
Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test L
RCM
B007E:2B
Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B007E:4A
Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B007F:11
Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground
GO to Pinpoint Test M
RCM
B007F:12
Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery
GO to Pinpoint Test M
RCM
B007F:13
Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open
GO to Pinpoint Test M
RCM
B007F:1A
Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test M
RCM
B007F:2B
Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B007F:4A
Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B0082:11
Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground
GO to Pinpoint Test N
RCM
B0082:12
Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery
GO to Pinpoint Test N
RCM
B0082:13
Passenger Seatbelt Load Limiter Deployment Control: Circuit Open
GO to Pinpoint Test N
RCM
B0082:1A
Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test N
RCM
B0082:2B
Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B0082:4A
Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B00A0:09
Occupant Classification System: Component Failure
GO to Pinpoint Test O
RCM
B00A0:4A
Occupant Classification System: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B00A0:63
Occupant Classification System: Circuit / Component Protection Time-Out
GO to Pinpoint Test O
RCM
B00A0:64
Occupant Classification System: Signal Plausibility Failure
GO to Pinpoint Test O
RCM
B00A0:68
Occupant Classification System: Event Information
GO to Pinpoint Test O
RCM
B00B5:11
Driver Seat Track Position Restraints Sensor: Circuit Short to Ground
GO to Pinpoint Test P
RCM
B00B5:12
Driver Seat Track Position Restraints Sensor: Circuit Short to Battery
GO to Pinpoint Test P
RCM
B00B5:13
Driver Seat Track Position Restraints Sensor: Circuit Open
GO to Pinpoint Test P
RCM
B00B5:1D
Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range
GO to Pinpoint Test P
RCM
B00B5:2B
Driver Seat Track Position Restraints Sensor: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B00B5:4A
Driver Seat Track Position Restraints Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B00C5:11
Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground
GO to Pinpoint Test Q
RCM
B00C5:12
Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery
GO to Pinpoint Test Q
RCM
B00C5:13
Passenger Seat Track Position Restraints Sensor: Circuit Open
GO to Pinpoint Test Q
RCM
B00C5:1D
Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range
GO to Pinpoint Test Q
RCM
B00C5:2B
Passenger Seat Track Position Restraints Sensor: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B00C5:4A
Passenger Seat Track Position Restraints Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B00D5:01
Restraint System Passenger Disable Indicator: General Electrical Failure
GO to Pinpoint Test R
RCM
B00D5:4A
Restraint System Passenger Disable Indicator: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1193:00
Crash Event Storage Full and Locked: No Sub Type Information
GO to Pinpoint Test S
RCM
B11CF:11
Passenger Frontal Airbag Canister Vent: Circuit Short to Ground
GO to Pinpoint Test T
RCM
B11CF:12
Passenger Frontal Airbag Canister Vent: Circuit Short to Battery
GO to Pinpoint Test T
RCM
B11CF:13
Passenger Frontal Airbag Canister Vent: Circuit Open
GO to Pinpoint Test T
RCM
B11CF:1A
Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold
GO to Pinpoint Test T
RCM
B11CF:2B
Passenger Frontal Airbag Canister Vent: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B11CF:4A
Passenger Frontal Airbag Canister Vent: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B11D8:11
Restraint Event Notification: Circuit Short To Ground
GO to Pinpoint Test U
RCM
B11D8:12
Restraint Event Notification: Circuit Short To Battery
GO to Pinpoint Test U
RCM
B11D8:13
Restraint Event Notification: Circuit Short To Open
GO to Pinpoint Test U
RCM
B1202:01
Restraint System Passenger Enable Indicator: General Electrical Failure
GO to Pinpoint Test V
RCM
B1202:4A
Restraint System Passenger Enable Indicator: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1404:11
Driver Side Airbag Deployment Control: Circuit Short to Ground
GO to Pinpoint Test W
RCM
B1404:12
Driver Side Airbag Deployment Control: Circuit Short to Battery
GO to Pinpoint Test W
RCM
B1404:13
Driver Side Airbag Deployment Control: Circuit Open
GO to Pinpoint Test W
RCM
B1404:1A
Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test W
RCM
B1404:2B
Driver Side Airbag Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B1404:4A
Driver Side Airbag Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1405:11
Driver Side Curtain Deployment Control 1: Circuit Short to Ground
GO to Pinpoint Test X
RCM
B1405:12
Driver Side Curtain Deployment Control 1: Circuit Short to Battery
GO to Pinpoint Test X
RCM
B1405:13
Driver Side Curtain Deployment Control 1: Circuit Open
GO to Pinpoint Test X
RCM
B1405:1A
Driver Side Curtain Deployment Control 1: Circuit Resistance Below Threshold
GO to Pinpoint Test X
RCM
B1405:2B
Driver Curtain Deployment Control 1: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B1405:4A
Driver Curtain Deployment Control 1: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1407:11
Passenger Side Airbag Deployment Control: Circuit Short to Ground
GO to Pinpoint Test Y
RCM
B1407:12
Passenger Side Airbag Deployment Control: Circuit Short to Battery
GO to Pinpoint Test Y
RCM
B1407:13
Passenger Side Airbag Deployment Control: Circuit Open
GO to Pinpoint Test Y
RCM
B1407:1A
Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test Y
RCM
B1407:2B
Passenger Side Airbag Deployment Control: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B1407:4A
Passenger Side Airbag Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1408:11
Passenger Side Curtain Deployment Control 1: Circuit Short to Ground
GO to Pinpoint Test Z
RCM
B1408:12
Passenger Side Curtain Deployment Control 1: Circuit Short to Battery
GO to Pinpoint Test Z
RCM
B1408:13
Passenger Side Curtain Deployment Control 1: Circuit Open
GO to Pinpoint Test Z
RCM
B1408:1A
Passenger Side Curtain Deployment Control 1: Circuit Resistance Below Threshold
GO to Pinpoint Test Z
RCM
B1408:2B
Passenger Curtain Deployment Control 1: Signal Cross Coupled
GO to Pinpoint Test AL
RCM
B1408:4A
Passenger Curtain Deployment Control 1: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B140C:11
Second Row Driver Side Seatbelt Sensor: Circuit Short to Ground
GO to Pinpoint Test AA
RCM
B140C:12
Second Row Driver Side Seatbelt Sensor: Circuit Short to Battery
GO to Pinpoint Test AA
RCM
B140C:13
Second Row Driver Side Seatbelt Sensor: Circuit Open
GO to Pinpoint Test AA
RCM
B140C:1D
Second Row Driver Side Seatbelt Sensor: Circuit Current Out of Range
GO to Pinpoint Test AA
RCM
B140C:2B
Second Row Driver Side Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B140C:4A
Second Row Driver Side Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B140D:11
Second Row Passenger Side Seatbelt Sensor: Circuit Short to Ground
GO to Pinpoint Test AB
RCM
B140D:12
Second Row Passenger Side Seatbelt Sensor: Circuit Short to Battery
GO to Pinpoint Test AB
RCM
B140D:13
Second Row Passenger Side Seatbelt Sensor: Circuit Open
GO to Pinpoint Test AB
RCM
B140D:1D
Second Row Passenger Side Seatbelt Sensor: Circuit Current Out of Range
GO to Pinpoint Test AB
RCM
B140D:2B
Second Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B140D:4A
Second Row Passenger Side Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B140E:11
Third Row Driver Side Seatbelt Sensor: Circuit Short To Ground
GO to Pinpoint Test AC
RCM
B140E:12
Third Row Driver Side Seatbelt Sensor: Circuit Short To Battery
GO to Pinpoint Test AC
RCM
B140E:13
Third Row Driver Side Seatbelt Sensor: Circuit Open
GO to Pinpoint Test AC
RCM
B140E:1D
Third Row Driver Side Seatbelt Sensor: Circuit Current Out Of Range
GO to Pinpoint Test AC
RCM
B140E:2B
Third Row Driver Side Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B140E:4A
Third Row Driver Side Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B140F:11
Third Row Passenger Side Seatbelt Sensor: Circuit Short To Ground
GO to Pinpoint Test AD
RCM
B140F:12
Third Row Passenger Side Seatbelt Sensor: Circuit Short To Battery
GO to Pinpoint Test AD
RCM
B140F:13
Third Row Passenger Side Seatbelt Sensor: Circuit Open
GO to Pinpoint Test AD
RCM
B140F:1D
Third Row Passenger Side Seatbelt Sensor: Circuit Current Out Of Range
GO to Pinpoint Test AD
RCM
B140F:2B
Third Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B140F:4A
Third Row Passenger Side Seatbelt Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1410:11
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground
GO to Pinpoint Test AE
RCM
B1410:12
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery
GO to Pinpoint Test AE
RCM
B1410:13
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Open
GO to Pinpoint Test AE
RCM
B1410:1A
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test AE
RCM
B1410:2B
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B1410:4A
Second Row Driver Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1412:11
Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground
GO to Pinpoint Test AF
RCM
B1412:12
Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery
GO to Pinpoint Test AF
RCM
B1412:13
Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Open
GO to Pinpoint Test AF
RCM
B1412:1A
Second Row Passenger Side Seatbelt
Pretensioner Deployment Control: Circuit Resistance Below Threshold
GO to Pinpoint Test AF
RCM
B1412:2B
Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled
GO to Pinpoint Test AL
RCM
B1412:4A
Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1413:11
Driver Frontal Restraints Sensor: Circuit Short to Ground
GO to Pinpoint Test AG
RCM
B1413:12
Driver Frontal Restraints Sensor: Circuit Short to Battery
GO to Pinpoint Test AG
RCM
B1413:13
Driver Frontal Restraints Sensor: Circuit Open
GO to Pinpoint Test AG
RCM
B1413:4A
Driver Frontal Restraints Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1413:81
Driver Frontal Restraints Sensor: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1413:96
Driver Frontal Restraints Sensor: Component Internal Failure
GO to Pinpoint Test AH
RCM
B1414:11
Driver Side Restraints Sensor 1: Circuit Short to Ground
GO to Pinpoint Test AI
RCM
B1414:12
Driver Side Restraints Sensor 1: Circuit Short to Battery
GO to Pinpoint Test AI
RCM
B1414:13
Driver Side Restraints Sensor 1: Circuit Open
GO to Pinpoint Test AI
RCM
B1414:4A
Driver Side Restraints Sensor 1: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1414:81
Driver Side Restraints Sensor 1: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1414:96
Driver Side Restraints Sensor 1: Component Internal Failure
GO to Pinpoint Test AH
RCM
B1415:11
Driver Side Restraints Sensor 2: Circuit Short to Ground
GO to Pinpoint Test AJ
RCM
B1415:12
Driver Side Restraints Sensor 2: Circuit Short to Battery
GO to Pinpoint Test AJ
RCM
B1415:13
Driver Side Restraints Sensor 2: Circuit Open
GO to Pinpoint Test AJ
RCM
B1415:4A
Driver Side Restraints Sensor 2: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1415:81
Driver Side Restraints Sensor 2: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1415:96
Driver Side Restraints Sensor 2: Component Internal Failure
GO to Pinpoint Test AH
RCM
B1417:11
Passenger Frontal Restraints Sensor: Circuit Short To Ground
GO to Pinpoint Test AK
RCM
B1417:12
Passenger Frontal Restraints Sensor: Circuit Short To Battery
GO to Pinpoint Test AK
RCM
B1417:13
Passenger Frontal Restraints Sensor: Circuit Open
GO to Pinpoint Test AK
RCM
B1417:4A
Passenger Frontal Restraints Sensor: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1417:81
Passenger Frontal Restraints Sensor: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1417:96
Passenger Frontal Restraints Sensor: Component Internal Failure
GO to Pinpoint Test AH
RCM
B1418:11
Passenger Side Restraints Sensor 1: Circuit Short to Ground
GO to Pinpoint Test AJ
RCM
B1418:12
Passenger Side Restraints Sensor 1: Circuit Short to Battery
GO to Pinpoint Test AJ
RCM
B1418:13
Passenger Side Restraints Sensor 1: Circuit Open
GO to Pinpoint Test AJ
RCM
B1418:4A
Passenger Side Restraints Sensor 1: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1418:81
Passenger Side Restraints Sensor 1: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1418:96
Passenger Side Restraints Sensor 1: Component Internal Failure
GO to Pinpoint Test AH
RCM
B1419:11
Passenger Side Restraints Sensor 2: Circuit Short to Ground
GO to Pinpoint Test AI
RCM
B1419:12
Passenger Side Restraints Sensor 2: Circuit Short to Battery
GO to Pinpoint Test AI
RCM
B1419:13
Passenger Side Restraints Sensor 2: Circuit Open
GO to Pinpoint Test AI
RCM
B1419:4A
Passenger Side Restraints Sensor 2: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1419:81
Passenger Side Restraints Sensor 2: Invalid Serial Data Received
GO to Pinpoint Test AH
RCM
B1419:96
Passenger Side Restraints Sensor 2: Component Internal Failure
GO to Pinpoint Test AH
RCM
B142D:00
Pyrotechnic End of Life Activation Performed: No Sub Type Information
GO to Pinpoint Test AV
RCM
B1469:4A
Unused Satellite Restraints Sensor 1: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B146A:4A
Unused Satellite Restraints Sensor 2: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1492:68
Fuel Cutoff Event: Event Information
GO to Pinpoint Test AW
RCM
B14ED:11
Restraint Event Notification 2: Circuit Short To Ground
GO to Pinpoint Test AX
RCM
B14ED:12
Restraint Event Notification 2: Circuit Short To Battery
GO to Pinpoint Test AX
RCM
B14ED:13
Restraint Event Notification 2: Circuit Open
GO to Pinpoint Test AX
RCM
B14EE:11
Restraint Event Notification 3: Circuit Short To Ground
GO to Pinpoint Test AY
RCM
B14EE:12
Restraint Event Notification 3: Circuit Short To Battery
GO to Pinpoint Test AY
RCM
B14EE:13
Restraint Event Notification 3: Circuit Open
GO to Pinpoint Test AY
RCM
B1534:4A
Unused Deployable Device: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
B1535:4A
Unused DC Sensor Device: Incorrect Component Installed
GO to Pinpoint Test AM
RCM
C0061:68
Lateral Acceleration Sensor: Event Information
GO to Pinpoint Test AN
RCM
C0062:68
Longitudinal Acceleration Sensor: Event Information
GO to Pinpoint Test AN
RCM
C0063:68
Yaw Rate Sensor: Event Information
GO to Pinpoint Test AN
RCM
C0064:68
Roll Rate Sensor: Event Information
GO to Pinpoint Test AN
RCM
C0065:68
Vertical Acceleration Sensor: Event Information
GO to Pinpoint Test AN
RCM
U0028:08
Vehicle Communication Bus A: Bus Signal/Message Failures
GO to Pinpoint Test AO
RCM
U0028:88
Vehicle Communication Bus A: Bus Off
GO to Pinpoint Test AO
RCM
U0100:00
Lost Communication with ECM/PCM “A”: No Sub Type Information
GO to Pinpoint Test AP
RCM
U0140:00
Lost Communication with Body Control Module: No Sub Type Information
GO to Pinpoint Test AQ
RCM
U0146:00
Lost Communication with Gateway "A": No Sub Type Information
GO to Pinpoint Test AR
RCM
U0154:00
Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information
GO to Pinpoint Test AS
RCM
U0253:00
Lost Communication with Accessory Protocol Interface Module: No Sub Type Information
GO to Pinpoint Test AT
RCM
U0300:00
Control Module: No Sub Type Information
GO to Pinpoint Test AV
RCM
U0401:00
Invalid Data Received from ECM/PCM A: No Sub Type Information
GO to Pinpoint Test AU
RCM
U0401:81
Invalid Data Received from ECM/PCM A: Invalid Serial Data Received
GO to Pinpoint Test AU
RCM
U0422:00
Invalid Data Received From Body Control Module: No Sub Type Information
GO to Pinpoint Test AU
RCM
U0422:81
Invalid Data Received From Body Control Module: Invalid Serial Data Received
GO to Pinpoint Test AU
RCM
U0455:81
Invalid Data Received From Restraints
Occupant Classification System Module: Invalid Serial Data Received
GO to Pinpoint Test AU
RCM
U0554:00
Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information
GO to Pinpoint Test AU
RCM
U0557:82
Invalid Data Received From Front Controls
Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated
GO to Pinpoint Test AU
RCM
U2024:57
Control Module Cal-Config Data: Invalid/Incompatible Software Component
GO to Pinpoint Test AV
RCM
U2100:00
Initial Configuration Not Complete: No Sub Type Information
GO to Pinpoint Test AZ
RCM
U2101:00
Control Module Configuration Incompatible: No Sub Type Information
GO to Pinpoint Test AO
RCM
U2200:00
Control Module Configuration Memory Corrupt: No Sub Type Information
GO to Pinpoint Test AV
RCM
U2300:55
Central Configuration: Not Configured
GO to Pinpoint Test BA
RCM
U2300:64
Central Configuration: Signal Plausibility Failure
GO to Pinpoint Test BA
RCM
U3000:04
Control Module: System Internal Failure
GO to Pinpoint Test AV
RCM
U3000:46
Control Module: Calibration / Parameter Memory Failure
GO to Pinpoint Test AV
RCM
U3000:49
Control Module: Internal Electronic Failure
GO to Pinpoint Test AV
RCM
U3003:16
Battery Voltage: Circuit Voltage Below Threshold
GO to Pinpoint Test BB
RCM
U3003:17
Battery Voltage: Circuit Voltage Above Threshold
GO to Pinpoint Test BB
Symptom Chart(s)
Symptom Chart: Supplemental Restraint System
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...