Lincoln Aviator: Starting a Hybrid Electric Vehicle System / Phone as a Key Backup Starting Passcode
Note: In order to use the Backup Start
Passcode feature, Phone as a Key must be
active and enabled on at least one phone.
If you are unable to start your vehicle, do the
following:
- Fully depress the brake pedal.
- SYNC displays the Backup Starting
Passcode entry screen.
- Using the SYNC display enter the backup
password and select Enter within 30
seconds.
- SYNC displays messages to start the
vehicle.
- Fully depress the brake pedal and press
the start button within 20 seconds to start
the engine.
Fast Restart
The fast restart feature allows you to restart
your vehicle within 20 seconds of switching
it off, even if it does not detect a valid
passive key...
Automatic Engine Shutdown
For vehicles with a keyless ignition, this
feature automatically shuts down the engine
if it has been idling for an extended period...
Other information:
Your vehicle has an Intelligent Oil-Life
Monitor that determines when you should
change the engine oil based on how you use
your vehicle. By using several important
factors in its calculations, the monitor helps
reduce the cost of owning your vehicle and
reduces environmental waste at the same
time...
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B11D9:16
Vehicle Battery:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
B11D9:17
Vehicle Battery:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U0100:87
Lost Communication With ECM/PCM "A":Missing Message
GO to Pinpoint Test A
BCM
U0121:87
Lost Communication With Anti-Lock Brake System (ABS) Control Module:Missing Message
GO to Pinpoint Test B
BCM
U0131:87
Lost Communication With Power Steering Control Module:Missing Message
GO to Pinpoint Test C
BCM
U0151:87
Lost Communication With Restraints Control Module:Missing Message
GO to Pinpoint Test D
BCM
U0155:87
Lost Communication With Instrument Panel Cluster (IPC) Control Module:Missing Message
GO to Pinpoint Test E
BCM
U0166:87
Lost Communication With Auxiliary Heater Control Module:Missing Message
GO to Pinpoint Test F
BCM
U0184:87
Lost Communication With Radio:Missing Message
GO to Pinpoint Test G
BCM
U0198:87
Lost Communication With Telematic Control Module: Missing Message
GO to Pinpoint Test H
BCM
U0199:87
Lost Communication With "Door Control Module A":Missing Message
GO to Pinpoint Test I
BCM
U019B:87
Lost Communication With Battery Charger Control Module:Missing Message
GO to Pinpoint Test J
BCM
U0200:87
Lost Communication With "Door Control Module B":Missing Message
GO to Pinpoint Test K
BCM
U0208:87
Lost Communication With "Seat Control Module A":Missing Message
GO to Pinpoint Test L
BCM
U0212:87
Lost Communication With Steering Column Control Module:Missing Message
GO to Pinpoint Test M
BCM
U0230:87
Lost Communication With Rear Gate Module:Missing Message
GO to Pinpoint Test N
BCM
U0232:87
Lost Communication With Side Obstacle Detection Control Module "A":Missing Message
GO to Pinpoint Test O
BCM
U0233:87
Lost Communication With Side Obstacle Detection Control Module "B":Missing Message
GO to Pinpoint Test P
BCM
U023A:87
Lost Communication With Image Processing Control Module A:Missing Message
GO to Pinpoint Test Q
BCM
U0252:87
Lost Communication With Lighting Control Module-Rear "B":Missing Message
GO to Pinpoint Test R
BCM
U0253:87
Lost Communication With Accessory Protocol Interface Module:Missing Message
GO to Pinpoint Test S
BCM
U0256:87
Lost Communication With Front Controls Interface Module "A":Missing Message
GO to Pinpoint Test T
BCM
U0293:87
Lost Communication With Hybrid/EV Powertrain Control Module "A":Missing Message
GO to Pinpoint Test U
BCM
U1000:00
Solid State Driver Protection Active:Driver Disabled: No Sub Type Information
GO to Pinpoint Test V
BCM
U2005:85
Vehicle Speed:Signal Above Allowable Range
GO to Pinpoint Test W
BCM
U2100:00
Initial Configuration Not Complete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2101:00
Control Module Configuration Inomplete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2200:00
Control Module Configuration Memory Corrupt:No Sub Type Information
GO to Pinpoint Test X
BCM
U3000:49
Control Module:Internal Electronic Failure
GO to Pinpoint Test AA
BCM
U3006:16
Control Module Input Power “A”:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3006:17
Control Module Input Power “A”:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Y
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Z
BCM
U3007:16
Control Module Input Power "B":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3007:17
Control Module Input Power "B":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3013:16
Control Module Input Power "C":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3013:17
Control Module Input Power "C":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3014:16
Control Module Input Power "D":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3014:17
Control Module Input Power "D":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
Symptom Chart
Symptom Chart: Multifunction Electronic Modules
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...