Lincoln Aviator: Capacities and Specifications - Plug-In Hybrid Electric Vehicle (PHEV) / Rear Axle
Capacities

Materials

Other information:
Special Tool(s) /
General Equipment
205-153
(T80T-4000-W)
Handle
303-1246Engine Spreader BarTKIT-2006UF-FLMTKIT-2006UF-ROW
303-1247VCT Spark Plug Tube Seal Remover and InstallerTKIT-2006UF-FLMTKIT-2006UF-ROW
303-1248Camshaft holding toolsTKIT-2006UF-FLMTKIT-2006UF-ROW
303-1634Lift Eyes (2)TKIT-2014D-ROW3TKIT-2014D-FL_ROW
303-1696Camshaft holding fixture
303-409
(T92C-6700-CH)
Remover, Crankshaft SealTKIT-1992-FH/FMH/FLMHTKIT-1993-LMH/MH
Floor Crane
Mounting Stand
Plastic Scraper
Flat-Bladed Screwdriver
Materials
Name
Specification
Motorcraft® Silicone Gasket RemoverZC-30-A
-
Motorcraft® Metal Surface Prep WipesZC-31-B
-
Motorcraft® Metal Brake Parts CleanerPM-4-A, PM-4-B
-
NOTICE:
During engine repair procedures, cleanliness is extremely
important...
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
ABS
B1111:4B
Electric Park Brake Enable:Over Temperature
GO to Pinpoint Test F
ABS
B1111:53
Electric Park Brake Enable:Deactivated
GO to Pinpoint Test G
ABS
B1111:54
Electric Park Brake Enable:Missing Calibration
GO to Pinpoint Test E
ABS
C0609:01
Park Brake Switch Circuit:General Electrical Failure
GO to Pinpoint Test B
ABS
C0616:9A
Park Brake Control Module Control Circuit Performance:Component or System Operating Conditions
GO to Pinpoint Test B
ABS
C1034:01
Park Brake:General Electrical Failure
GO to Pinpoint Test B
ABS
C1034:07
Park Brake:Mechanical Failures
GO to Pinpoint Test K
ABS
C1034:13
Park Brake:Circuit Open
GO to Pinpoint Test B
ABS
C1034:25
Park Brake:Signal Shape/Waveform Failure
GO to Pinpoint Test B
ABS
C1034:2F
Park Brake:Signal Erratic
GO to Pinpoint Test B
ABS
C1034:47
Park Brake:Watchdog/Safety µC Failure
GO to Pinpoint Test B
ABS
C1034:48
Park Brake:Supervision Software Failure
GO to Pinpoint Test B
ABS
C1034:57
Park Brake:Invalid/Incompatible Software Component
GO to Pinpoint Test B
ABS
C1034:71
Park Brake:Actuator Stuck
GO to Pinpoint Test C
ABS
C1034:77
Park Brake:Commanded Position Not Reachable
GO to Pinpoint Test C
ABS
C1034:78
Park Brake:Alignment Or Adjustment Incorrect
GO to Pinpoint Test H
ABS
C1034:97
Park Brake:Component or System Operation Obstructed or Blocked
GO to Pinpoint Test D
ABS
C1A43:98
Motor Supply:Component or System Over Temperature
GO to Pinpoint Test D
ABS
C2005:18
Right Actuator:Circuit Current Below Threshold
GO to Pinpoint Test D
ABS
C2005:19
Right Actuator:Circuit Current Above Threshold
GO to Pinpoint Test D
ABS
C2005:77
Right Actuator:Commanded Position Not Reachable
GO to Pinpoint Test C
ABS
C2005:78
Right Actuator:Alignment Or Adjustment Incorrect
GO to Pinpoint Test A
ABS
C2006:18
Left Actuator:Circuit Current Below Threshold
GO to Pinpoint Test D
ABS
C2006:19
Left Actuator:Circuit Current Above Threshold
GO to Pinpoint Test D
ABS
C2006:77
Left Actuator:Commanded Position Not Reachable
GO to Pinpoint Test C
ABS
C2006:78
Left Actuator:Alignment Or Adjustment Incorrect
GO to Pinpoint Test A
ABS
C2007:13
Right Motor:Circuit Open
GO to Pinpoint Test D
ABS
C2007:1C
Right Motor:Circuit Voltage Out Of Range
GO to Pinpoint Test D
ABS
C2007:92
Right Motor:Performance Or Incorrect Operation
GO to Pinpoint Test D
ABS
C2008:13
Left Motor:Circuit Open
GO to Pinpoint Test D
ABS
C2008:1C
Left Motor:Circuit Voltage Out Of Range
GO to Pinpoint Test D
ABS
C2008:92
Left Motor:Performance Or Incorrect Operation
GO to Pinpoint Test D
ABS
U2002:00
Switch:No Sub Type Information
GO to Pinpoint Test J
ABS
U2002:47
Switch:Watchdog/Safety µC Failure
GO to Pinpoint Test B
Symptom Chart(s)
Symptom Chart: Parking Brake and Actuation
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Categories
Each door has a backup power system which
allows the door to function if your vehicle
has no power. The system has a limited
number of operations before the power is
depleted and turns off. When the system
turns off, the door remains open and
unlatched and does not close.
If your vehicle has no power and the backup
power system is turned off, you can close
and secure your vehicle by manually
resetting each door latch using a key in the
position shown.
read more