Lincoln Aviator: Climate Control System - General Information / Removal and Installation - Air Inlet Door Actuator
Removal
-
Remove the climate control housing.
Refer to: Climate Control Housing (412-00 Climate Control System - General Information, Removal and Installation).
-
Remove the screws and the air inlet door actuator.
-
Disconnect the electrical connector.
Installation
-
To install, reverse the removal procedure.
Removal
Fully lower the glove compartment.
Disconnect the check strap.
Push the stop tabs inward.
Remove the screws and the air distribution door actuator...
Removal
NOTE:
Removal steps in this procedure may contain installation details.
Remove the front bumper cover.
Refer to: Front Bumper Cover (501-19 Bumpers, Removal and Installation)...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B108A:01
Start Button: General Electrical Failure
GO to Pinpoint Test A
BCM
B108A:24
Start Button: Signal Stuck High
GO to Pinpoint Test A
BCM
B1142:29
Ignition Status 1: Signal Invalid
GO to Pinpoint Test A
BCM
B1240:11
Start Button Mode Indicator: Circuit Short to Ground
GO to Pinpoint Test B
BCM
B1240:15
Start Button Mode Indicator: Circuit Short to Battery or Open
GO to Pinpoint Test C
BCM
B1310:12
Run/Start Control: Circuit Short to Battery
GO to Pinpoint Test A
BCM
B1310:14
Run/Start Control: Circuit Short to Ground or Open
GO to Pinpoint Test A
SCCM
B112B:04
SCCM:Steering Wheel Module: System Internal Failure
GO to Pinpoint Test I
SCCM
B112B:44
SCCM:Steering Wheel Module: Data Memory Failure
GO to Pinpoint Test I
SCCM
B112B:45
SCCM:Steering Wheel Module: Program Memory Failure
GO to Pinpoint Test I
SCCM
B112B:46
SCCM:Steering Wheel Module: Calibration / Parameter Memory Failure
GO to Pinpoint Test I
SCCM
B112B:49
SCCM:Steering Wheel Module: Internal Electronic Failure
GO to Pinpoint Test I
SCCM
B135C:11
Heater Element:Circuit Short To Ground
GO to Pinpoint Test G
SCCM
B135C:13
Heater Element:Circuit Open
GO to Pinpoint Test G
SCCM
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test H
SCCM
U0140:00
SCCM:Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U0146:00
SCCM:Lost Communication With Gateway "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0146:87
SCCM:Lost Communication With Gateway "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0155:00
SCCM:Lost Communication With Instrument Panel Cluster Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U023A:00
SCCM:Lost Communication With Image Processing Module "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0241:00
SCCM:Lost Communication With Headlamp Control Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U210A:11
Temperature Sensor:Circuit Short To Ground
GO to Pinpoint Test G
SCCM
U210A:13
Temperature Sensor:Circuit Open
GO to Pinpoint Test G
SCCM
U3003:A2
Battery Voltage: System Voltage Low
GO to Pinpoint Test E
SCCM
U3003:A3
Battery Voltage:System Voltage High
GO to Pinpoint Test F
SECM
B135C:11
Heater Element:Circuit Short To Ground
GO to Pinpoint Test K
SECM
B135C:15
Heater Element:Circuit Short to Battery or Open
GO to Pinpoint Test K
SECM
B13BD:92
Steering Wheel Heater Module:Performance or Incorrect Operation
GO to Pinpoint Test K
SECM
U1000:00
Solid State Driver Protection Active:No Sub Type Information
GO to Pinpoint Test K
SECM
U210A:02
Temperature Sensor:General Signal Failure
GO to Pinpoint Test K
SECM
U210A:11
Temperature Sensor:Circuit Short to Ground
GO to Pinpoint Test K
SECM
U210A:15
Temperature Sensor:Circuit Short to Battery or Open
GO to Pinpoint Test K
SIMA
U0100:00
Lost Communication With ECM/PCM "A": No Sub Type Information
GO to Pinpoint Test L
SIMA
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test L
SIMA
U3003:16
Battery Voltage:Battery Voltage Below Threshold
GO to Pinpoint Test M
SIMA
U3003:17
Battery Voltage:Battery Voltage Above Threshold
GO to Pinpoint Test N
Symptom Charts
Symptom Chart: Ignition Switch - Push Button
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Removal
NOTE:
This step is only necessary if the HCM is being replaced.
NOTE:
If installing a new module, it is necessary to
upload the module configuration information to the scan tool prior to
removing the module. This information must be downloaded into the new
module after installation...