Lincoln Aviator: Maintenance / Washer Fluid Check. Fuel Filter. Checking the Wiper Blades
Washer Fluid Check
WARNING: If you operate your
vehicle in temperatures below 41.0°F (5°C),
use washer fluid with antifreeze protection.
Failure to use washer fluid with antifreeze
protection in cold weather could result in
impaired windshield vision and increase
the risk of injury or accident.
Note: The front and rear washer systems
are supplied from the same reservoir.
Add fluid to fill the reservoir if the level is low.
Only use a washer fluid that meets our
specifications.
State or local regulations on volatile organic
compounds may restrict the use of methanol,
a common windshield washer antifreeze
additive. Washer fluids containing
non-methanol antifreeze agents should be
used only if they provide cold weather
protection without damaging the vehicle’s
paint finish, wiper blades or washer system.
Fuel Filter
Your vehicle is equipped with a lifetime fuel
filter that is integrated with the fuel tank.
Regular maintenance or replacement is not
needed.
Checking the Wiper Blades
Run the tip of your fingers over the edge of
the blade to check for roughness.
Clean the wiper blades with washer fluid or
water applied with a soft sponge or cloth.
Vertical Aim Adjustment
If your vehicle has been involved in a crash,
have the aim of the headlamp beam checked
by an authorized dealer.
8 ft (2.4 m)...
You can improve poor wiper quality by
cleaning the wiper blades and the
windshield.
Replace the wiper blades at least annually
for optimum performance...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
GSM
P0562:00
System Voltage Low: No Sub Type Information
GO to Pinpoint Test B
GSM
P0563:00
System Voltage High: No Sub Type Information
GO to Pinpoint Test C
GSM
P0605:00
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information
GO to Pinpoint Test L
GSM
P0606:00
Control Module Processor: No Sub Type Information
GO to Pinpoint Test L
GSM
P0607:00
Control Module Performance: No Sub Type Information
GO to Pinpoint Test L
GSM
P06B8:00
Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information
GO to Pinpoint Test L
GSM
P07EC:00
Transmission Range Multi-Function Select Circuit: No Sub Type Information
GO to Pinpoint Test J
GSM
P07ED:00
Transmission Range Multi-Function Select Circuit Stuck: No Sub Type Information
GO to Pinpoint Test J
GSM
P0814:00
Transmission Range Display Circuit: No Sub Type Information
GO to Pinpoint Test I
GSM
P164E:00
Internal Control Module Transmission Range Select Performance: No Sub Type Information
GO to Pinpoint Test L
GSM
P166B:00
Drivers Door Status Correlation: No Sub Type Information
GO to Pinpoint Test H
GSM
U0100:00
Lost Communication With ECM/PCM "A": No Sub Type Information
GO to Pinpoint Test G
GSM
U0100:87
Lost Communication With ECM/PCM "A": Missing Message
GO to Pinpoint Test G
GSM
U0121:00
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information
GO to Pinpoint Test F
GSM
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test E
GSM
U0155:00
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information
GO to Pinpoint Test D
GSM
U0203:00
Lost Communication With Door Control Module "E": No Sub Type Information
GO to Pinpoint Test H
GSM
U0301:00
Software Incompatibility with ECM/PCM: No Sub Type Available
GO to Pinpoint Test M
GSM
U0401:00
Invalid Data Received from ECM/PCM A: No Sub Type Information
GO to Pinpoint Test N
GSM
U0422:00
Invalid Data Received From Body Control Module: No Sub Type Information
GO to Pinpoint Test N
GSM
U0504:00
Invalid Data Received From Door Control Module "E": No Sub Type Information
GO to Pinpoint Test H
GSM
U1011:00
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information
GO to Pinpoint Test O
GSM
U101F:00
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information
GO to Pinpoint Test O
Global Customer Symptom Code (GCSC) Chart
Global Customer Symptom Code Chart
Customer Symptom
Action
Start/Run/Move > Moving > Paddle Shift > Inoperative
GO to Pinpoint Test K
Start/Run/Move > Moving > Gear Selector > Return to Park
GO to Pinpoint Test Q
Start/Run/Move > Moving > Gear Selector > Return to Park
GO to Pinpoint Test R
Start/Run/Move > Moving > Engagement Quality > Park
GO to Pinpoint Test P
Start/Run/Move > Moving > Engagement Quality > Park
GO to Pinpoint Test S
Start/Run/Move > Moving > Gear Selector > Progressive Range Selection
GO to Pinpoint Test A
Pinpoint Tests
PINPOINT TEST A : PROGRESSIVE RANGE SELECTION DOES NOT OPERATE CORRECTLY
Refer to Wiring Diagrams Cell 30 for schematic and connector information...
Each door has a backup power system which
allows the door to function if your vehicle
has no power. The system has a limited
number of operations before the power is
depleted and turns off. When the system
turns off, the door remains open and
unlatched and does not close...