Lincoln Aviator: SYNC™ 3 / Phone
WARNING: Driving while distracted
can result in loss of vehicle control, crash
and injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.
Check the compatibility of your device on
the regional website.
Touch the climate button on the touchscreen
to access your climate control features.
Note: You can switch temperature units
between Fahrenheit and Celsius...
Go to the settings menu on your cell phone
and switch Bluetooth on.
Select the phone option on the
feature bar.
Select Add Phone.Note: A prompt alerts you to search for
your
vehicle on your cell phone...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B108A:01
Start Button: General Electrical Failure
GO to Pinpoint Test A
BCM
B108A:24
Start Button: Signal Stuck High
GO to Pinpoint Test A
BCM
B1142:29
Ignition Status 1: Signal Invalid
GO to Pinpoint Test A
BCM
B1240:11
Start Button Mode Indicator: Circuit Short to Ground
GO to Pinpoint Test B
BCM
B1240:15
Start Button Mode Indicator: Circuit Short to Battery or Open
GO to Pinpoint Test C
BCM
B1310:12
Run/Start Control: Circuit Short to Battery
GO to Pinpoint Test A
BCM
B1310:14
Run/Start Control: Circuit Short to Ground or Open
GO to Pinpoint Test A
SCCM
B112B:04
SCCM:Steering Wheel Module: System Internal Failure
GO to Pinpoint Test I
SCCM
B112B:44
SCCM:Steering Wheel Module: Data Memory Failure
GO to Pinpoint Test I
SCCM
B112B:45
SCCM:Steering Wheel Module: Program Memory Failure
GO to Pinpoint Test I
SCCM
B112B:46
SCCM:Steering Wheel Module: Calibration / Parameter Memory Failure
GO to Pinpoint Test I
SCCM
B112B:49
SCCM:Steering Wheel Module: Internal Electronic Failure
GO to Pinpoint Test I
SCCM
B135C:11
Heater Element:Circuit Short To Ground
GO to Pinpoint Test G
SCCM
B135C:13
Heater Element:Circuit Open
GO to Pinpoint Test G
SCCM
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test H
SCCM
U0140:00
SCCM:Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U0146:00
SCCM:Lost Communication With Gateway "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0146:87
SCCM:Lost Communication With Gateway "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0155:00
SCCM:Lost Communication With Instrument Panel Cluster Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U023A:00
SCCM:Lost Communication With Image Processing Module "A": No Sub Type Information
GO to Pinpoint Test J
SCCM
U0241:00
SCCM:Lost Communication With Headlamp Control Module: No Sub Type Information
GO to Pinpoint Test J
SCCM
U210A:11
Temperature Sensor:Circuit Short To Ground
GO to Pinpoint Test G
SCCM
U210A:13
Temperature Sensor:Circuit Open
GO to Pinpoint Test G
SCCM
U3003:A2
Battery Voltage: System Voltage Low
GO to Pinpoint Test E
SCCM
U3003:A3
Battery Voltage:System Voltage High
GO to Pinpoint Test F
SECM
B135C:11
Heater Element:Circuit Short To Ground
GO to Pinpoint Test K
SECM
B135C:15
Heater Element:Circuit Short to Battery or Open
GO to Pinpoint Test K
SECM
B13BD:92
Steering Wheel Heater Module:Performance or Incorrect Operation
GO to Pinpoint Test K
SECM
U1000:00
Solid State Driver Protection Active:No Sub Type Information
GO to Pinpoint Test K
SECM
U210A:02
Temperature Sensor:General Signal Failure
GO to Pinpoint Test K
SECM
U210A:11
Temperature Sensor:Circuit Short to Ground
GO to Pinpoint Test K
SECM
U210A:15
Temperature Sensor:Circuit Short to Battery or Open
GO to Pinpoint Test K
SIMA
U0100:00
Lost Communication With ECM/PCM "A": No Sub Type Information
GO to Pinpoint Test L
SIMA
U0140:00
Lost Communication With Body Control Module: No Sub Type Information
GO to Pinpoint Test L
SIMA
U3003:16
Battery Voltage:Battery Voltage Below Threshold
GO to Pinpoint Test M
SIMA
U3003:17
Battery Voltage:Battery Voltage Above Threshold
GO to Pinpoint Test N
Symptom Charts
Symptom Chart: Ignition Switch - Push Button
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Distance Indication and Alert is a function
that provides the driver with a graphical
indication of the time gap to other preceding
vehicles traveling in the same direction.
Distance Indication and Alert shows one of
the graphics that follow in the information
display...
Categories
Each door has a backup power system which
allows the door to function if your vehicle
has no power. The system has a limited
number of operations before the power is
depleted and turns off. When the system
turns off, the door remains open and
unlatched and does not close.
If your vehicle has no power and the backup
power system is turned off, you can close
and secure your vehicle by manually
resetting each door latch using a key in the
position shown.
read more