Lincoln Aviator: Apps / Using Mobile Navigation on an Android Device
- Connect your device to a USB port.
- Switch Android Auto off.
- Switch on Enable Mobile Apps via USB
in the Mobile Apps Settings tile.
- Select the apps option on the feature bar.
- Select the navigation app that you want
to use on the touchscreen.
Note: When using a navigation app, keep
your device unlocked and the app open.
Select the apps option on the
feature bar.
If your device is connected via USB,
switch Android Auto off.
Pair your device.
Start the apps on your device that you
want to use through SYNC...
WARNING: Driving while distracted
can result in loss of vehicle control, crash
and injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B11DB:02
Battery Monitoring Module "A": General Signal Failure
GO to Pinpoint Test F
BCM
B11DB:08
Battery Monitoring Module "A": Bus Signal/Message Failures
GO to Pinpoint Test F
BCM
B11DB:09
Battery Monitoring Module "A": Component Failures
GO to Pinpoint Test F
BCM
B11DB:11
Battery Monitoring Module "A": Circuit Short To Ground
GO to Pinpoint Test F
BCM
B11DB:49
Battery Monitoring Module "A": Internal Electronic Failure
GO to Pinpoint Test I
BCM
B11DB:55
Battery Monitoring Module "A": Not Configured
GO to Pinpoint Test J
BCM
B1489:11
Battery Monitoring System (BMS) Sensor Power: Circuit Short To Ground
GO to Pinpoint Test F
PCM
P0562:00
System Voltage Low: No Sub Type Information
GO to Pinpoint Test B
PCM
P0563:00
System Voltage High: No Sub Type Information
GO to Pinpoint Test A
PCM
P065B:00
Generator "A" Control Circuit Range/Performance: No Sub Type Information
GO to Pinpoint Test B
PCM
P065C:00
Generator "A" Mechanical Performance: No Sub Type Information
GO to Pinpoint Test B
PCM
P0A3B:00
Generator "A" Over Temperature: No Sub Type Information
GO to Pinpoint Test K
PCM
P0A5A:00
Generator Current Sensor Circuit Range/Performance: No Sub Type Information
GO to Pinpoint Test E
PCM
P0A5B:00
Generator Current Sensor Circuit Low: No Sub Type Information
GO to Pinpoint Test E
PCM
P0A5C:00
Generator Current Sensor Circuit High: No Sub Type Information
GO to Pinpoint Test E
PCM
U012D:00
Lost Communication With Generator "A" Control Module: No Sub Type Information
GO to Pinpoint Test G
PCM
U042E:00
Invalid Data Received From Generator "A" Control Module: No Sub Type Information
GO to Pinpoint Test G
Inspection and Verification
Verify the customer concern by operating the charging system...
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B11D9:16
Vehicle Battery:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
B11D9:17
Vehicle Battery:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U0100:87
Lost Communication With ECM/PCM "A":Missing Message
GO to Pinpoint Test A
BCM
U0121:87
Lost Communication With Anti-Lock Brake System (ABS) Control Module:Missing Message
GO to Pinpoint Test B
BCM
U0131:87
Lost Communication With Power Steering Control Module:Missing Message
GO to Pinpoint Test C
BCM
U0151:87
Lost Communication With Restraints Control Module:Missing Message
GO to Pinpoint Test D
BCM
U0155:87
Lost Communication With Instrument Panel Cluster (IPC) Control Module:Missing Message
GO to Pinpoint Test E
BCM
U0166:87
Lost Communication With Auxiliary Heater Control Module:Missing Message
GO to Pinpoint Test F
BCM
U0184:87
Lost Communication With Radio:Missing Message
GO to Pinpoint Test G
BCM
U0198:87
Lost Communication With Telematic Control Module: Missing Message
GO to Pinpoint Test H
BCM
U0199:87
Lost Communication With "Door Control Module A":Missing Message
GO to Pinpoint Test I
BCM
U019B:87
Lost Communication With Battery Charger Control Module:Missing Message
GO to Pinpoint Test J
BCM
U0200:87
Lost Communication With "Door Control Module B":Missing Message
GO to Pinpoint Test K
BCM
U0208:87
Lost Communication With "Seat Control Module A":Missing Message
GO to Pinpoint Test L
BCM
U0212:87
Lost Communication With Steering Column Control Module:Missing Message
GO to Pinpoint Test M
BCM
U0230:87
Lost Communication With Rear Gate Module:Missing Message
GO to Pinpoint Test N
BCM
U0232:87
Lost Communication With Side Obstacle Detection Control Module "A":Missing Message
GO to Pinpoint Test O
BCM
U0233:87
Lost Communication With Side Obstacle Detection Control Module "B":Missing Message
GO to Pinpoint Test P
BCM
U023A:87
Lost Communication With Image Processing Control Module A:Missing Message
GO to Pinpoint Test Q
BCM
U0252:87
Lost Communication With Lighting Control Module-Rear "B":Missing Message
GO to Pinpoint Test R
BCM
U0253:87
Lost Communication With Accessory Protocol Interface Module:Missing Message
GO to Pinpoint Test S
BCM
U0256:87
Lost Communication With Front Controls Interface Module "A":Missing Message
GO to Pinpoint Test T
BCM
U0293:87
Lost Communication With Hybrid/EV Powertrain Control Module "A":Missing Message
GO to Pinpoint Test U
BCM
U1000:00
Solid State Driver Protection Active:Driver Disabled: No Sub Type Information
GO to Pinpoint Test V
BCM
U2005:85
Vehicle Speed:Signal Above Allowable Range
GO to Pinpoint Test W
BCM
U2100:00
Initial Configuration Not Complete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2101:00
Control Module Configuration Inomplete:No Sub Type Information
GO to Pinpoint Test X
BCM
U2200:00
Control Module Configuration Memory Corrupt:No Sub Type Information
GO to Pinpoint Test X
BCM
U3000:49
Control Module:Internal Electronic Failure
GO to Pinpoint Test AA
BCM
U3006:16
Control Module Input Power “A”:Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3006:17
Control Module Input Power “A”:Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Y
BCM
U3006:1C
Control Module Input Power “A”:Circuit Voltage Out of Range
GO to Pinpoint Test Z
BCM
U3007:16
Control Module Input Power "B":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3007:17
Control Module Input Power "B":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3013:16
Control Module Input Power "C":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3013:17
Control Module Input Power "C":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
BCM
U3014:16
Control Module Input Power "D":Circuit Voltage Below Threshold
GO to Pinpoint Test Y
BCM
U3014:17
Control Module Input Power "D":Circuit Voltage Above Threshold
GO to Pinpoint Test Z
Symptom Chart
Symptom Chart: Multifunction Electronic Modules
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...