Lincoln Aviator: SYNC™ 3 Troubleshooting / Resetting the System
- Simultaneously press and hold the seek
up and the audio unit power buttons until
the screen goes black.
- Wait three minutes to allow the system
to complete the reset.
- Press the audio unit power button to
switch the system on.
Note: You can reset the system to restore
functionality that has stopped working. The
system reset is designed to restore
functionality and not delete any data that
you have stored.
Additional Information and Assistance
For additional information and assistance,
we recommend that you contact an
authorized dealer or refer to our website.
For a complete listing of the accessories that
are available for your vehicle, please contact
your authorized dealer or visit the online
store website:
Web Address (United States)
www...
Other information:
Body
repairs usually require a significant level of intervention in the
existing body shell structure. The corrosion protection, seals and NVH components are destroyed and must be replaced.
To
prevent the vehicle quality from being compromised due to a poor
quality repair, all repairs must be inspected during and after the
accident repair...
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B130F:12
Run Accessory Control: Circuit Short To Battery
GO to Pinpoint Test A
BCM
B130F:14
Run Accessory Control: Circuit Short To Ground or Open
GO to Pinpoint Test A
BCM
B130F:14
Run Accessory Control: Circuit Short To Ground or Open
GO to Pinpoint Test D
SCCM
B10AD:02
Rain Sensor: General Signal Failure
GO to Pinpoint Test F
SCCM
B10AD:08
Rain Sensor: Bus Signal / Message Failure
GO to Pinpoint Test F
SCCM
B10AD:49
Rain Sensor:Internal Electronic Failure
GO to Pinpoint Test Q
SCCM
B10AD:55
:Rain Sensor:Not Configured
GO to Pinpoint Test P
SCCM
B1131:02
Wiper motor module: General Signal Failure
GO to Pinpoint Test A
SCCM
B1131:02
Wiper Motor Module: General Signal Failure
GO to Pinpoint Test D
SCCM
B1131:08
Wiper motor module: Bus Signal / Message Failure
GO to Pinpoint Test B
SCCM
B1131:11
Wiper motor module: Circuit Short to Ground
GO to Pinpoint Test B
SCCM
B1131:49
Wiper Motor Module:Internal Electronic Failure
GO to Pinpoint Test R
SCCM
B1131:55
:Wiper Motor Module: Not Configured
GO to Pinpoint Test P
SCCM
B124E:11
Wiper Stalk Switch Pack: Circuit Short To Ground
GO to Pinpoint Test V
SCCM
B124E:13
Wiper Stalk Switch Pack: Circuit Open
GO to Pinpoint Test V
SCCM
B124E:55
Wiper Stalk Switch: Not Configured
GO to Pinpoint Test V
SCCM
B124E:96
Wiper Stalk Switch Pack: Component Internal Failure
GO to Pinpoint Test V
SCCM
B124E:9E
Wiper Stalk Switch Pack: Stuck On
GO to Pinpoint Test V
Symptom Chart
Symptom Chart: Wiper and Washer
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Categories

Use a child restraint (sometimes called an
infant carrier, convertible seat, or toddler
seat) for infants, toddlers and children
weighing 40 lb (18 kg) or less (generally
four-years-old or younger).
Using Lap and Shoulder Belts
WARNING: Do not place a rearward
facing child restraint in front of an active
airbag. Failure to follow this instruction
could result in personal injury or death.
read more