Lincoln Aviator: Parking Aids / 360 Degree Camera (If Equipped)
WARNING: The 360 degree camera
system still requires the driver to use it in
conjunction with looking out of the
windows, and checking the interior and
exterior mirrors for maximum coverage.
WARNING: Objects that are close to
either corner of the bumper or under the
bumper, might not be seen on the screen
due to the limited coverage of the camera
system.
WARNING: Use caution when turning
camera features on or off when the
transmission is not in park (P). Make sure
your vehicle is not moving.
WARNING: You are responsible for
controlling your vehicle at all times. The
system is designed to be an aid and does
not relieve you of your responsibility to
drive with due care and attention. Failure
to follow this instruction could result in the
loss of control of your vehicle, personal
injury or death.
Note: Use caution using the 360 view when
any of the doors are ajar. If a door is ajar,
the camera will be out of position and the
video image may be incorrect.
The 360 degree camera system consists of
front, side and rear cameras. The system:
- Allows you to see what is directly in front
or behind your vehicle.
- Provides cross traffic view in front and
behind your vehicle.
- Allows you to see a top-down view of the
area outside your vehicle, including the
blind spots.
- Provides visibility around your vehicle to
you in parking maneuvers such as:
- Centering in a parking space.
- Obstacles near vehicle.
- Parallel parking.
The front camera enable button
is
located near the display screen
and turns on the front camera
when your vehicle is not in reverse (R). This
camera is only available at slow parking
speeds.
Selectable settings for this feature are ON
and OFF.
The default setting for the rear camera delay
is OFF.
When shifting the transmission out of reverse
(R) and into any gear other than park (P), the
camera image remains in the display until:
Your vehicle speed reaches
approximately 5 mph (8 km/h)...
Note: The 360 degree camera system turns
off when your vehicle is in motion at low
speed, except when in reverse (R).
The front and rear cameras have multiple
screens which consist of: normal view with
360, normal view, and split view...
Other information:
Diagnostic Trouble Code (DTC) Chart
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).
Diagnostic Trouble Code Chart
Module
DTC
Description
Action
BCM
B14E0:11
Exterior Lamps Power Supply "C": Circuit Short to Ground
GO to Pinpoint Test A
BCM
B14E0:15
Exterior Lamps Power Supply "C": Circuit Short to Battery or Open
GO to Pinpoint Test A
BCM
B14E1:11
Exterior Lamps Power Supply "D": Circuit Short to Ground
GO to Pinpoint Test A
BCM
B14E1:15
Exterior Lamps Power Supply "D": Circuit Short to Battery or Open
GO to Pinpoint Test A
BCM
B14E2:11
Exterior Lamps Power Supply "E": Circuit Short to Ground
GO to Pinpoint Test B
BCM
B14E2:15
Exterior Lamps Power Supply "E": Circuit Short to Battery or Open
GO to Pinpoint Test B
BCM
B14E3:11
Exterior Lamps Power Supply "F": Circuit Short to Ground
GO to Pinpoint Test B
BCM
B14E3:15
Exterior Lamps Power Supply "F": Circuit Short to Battery or Open
GO to Pinpoint Test B
BCM
B14E5:01
Left Front Enhanced Exterior Lighting System: General Electrical Failure
GO to Pinpoint Test S
BCM
B14E5:08
Left Front Enhanced Exterior Lighting System: Bus Signal / Message Failure
GO to Pinpoint Test S
BCM
B14E5:49
Left Front Enhanced Exterior Lighting System: Internal Electronic Failure
GO to Pinpoint Test S
BCM
B14E5:55
Left Front Enhanced Exterior Lighting System: Not Configured
GO to Pinpoint Test S
BCM
B14E7:01
Right Front Enhanced Exterior Lighting System: General Electrical Failure
GO to Pinpoint Test S
BCM
B14E7:08
Right Front Enhanced Exterior Lighting System: Bus Signal / Message Failure
GO to Pinpoint Test S
BCM
B14E7:49
Right Front Enhanced Exterior Lighting System: Internal Electronic Failure
GO to Pinpoint Test S
BCM
B14E7:55
Right Front Enhanced Exterior Lighting System: Not Configured
GO to Pinpoint Test S
BCM
B1533:02
Headlamp Switch Module: General Signal Failure
GO to Pinpoint Test A
BCM
B1533:08
Headlamp Switch Module: Bus Signal / Message
GO to Pinpoint Test A
BCM
B1533:49
Headlamp Switch Module: Internal Electronic Failure
GO to Pinpoint Test A
BCM
B1533:56
Headlamp Switch Module: Invalid / Incompatible Configuration
GO to Pinpoint Test A
BCM
B1D00:11
Left Low Beam: Circuit Short To Ground
GO to Pinpoint Test A
BCM
B1D00:15
Left Low Beam: Circuit Short To Battery Or Open
GO to Pinpoint Test A
BCM
B1D01:11
Right Low Beam: Circuit Short To Ground
GO to Pinpoint Test A
BCM
B1D01:15
Right Low Beam: Circuit Short To Battery Or Open
GO to Pinpoint Test A
BCM
B1D02:11
Left High Beam Circuit: Circuit Short To Ground
GO to Pinpoint Test B
BCM
B1D02:15
Left High Beam Circuit: Circuit Short To Battery Or Open
GO to Pinpoint Test B
BCM
B1D03:11
Right High Beam Circuit: Circuit Short To Ground
GO to Pinpoint Test B
BCM
B1D03:15
Right High Beam Circuit: Circuit Short To Battery Or Open
GO to Pinpoint Test B
HCM
B1041:04
Levelling Control: System Internal Failure
GO to Pinpoint Test H
HCM
B1041:54
Levelling Control: Missing Calibration
GO to Pinpoint Test H
HCM
B1087:83
LIN Bus "A": Value of Signal Protection Calculation Incorrect
GO to Pinpoint Test F
HCM
B1087:83
LIN Bus "A": Value of Signal Protection Calculation Incorrect
GO to Pinpoint Test G
HCM
B1087:86
LIN Bus "A": Signal Invalid
GO to Pinpoint Test F
HCM
B1087:86
LIN Bus "A": Signal Invalid
GO to Pinpoint Test G
HCM
B1088:83
LIN Bus "B": Value of Signal Protection Calculation Incorrect
GO to Pinpoint Test F
HCM
B1088:83
LIN Bus "B": Value of Signal Protection Calculation Incorrect
GO to Pinpoint Test G
HCM
B1088:86
LIN Bus "B": Signal Invalid
GO to Pinpoint Test F
HCM
B1088:86
LIN Bus "B": Signal Invalid
GO to Pinpoint Test G
HCM
B1437:01
Left Levelling Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B1437:87
Left Levelling Actuator: Missing Message
GO to Pinpoint Test F
HCM
B1437:87
Left Levelling Actuator: Missing Message
GO to Pinpoint Test G
HCM
B1439:01
Right Levelling Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B1439:87
Right Levelling Actuator: Missing Message
GO to Pinpoint Test F
HCM
B1439:87
Right Levelling Actuator: Missing Message
GO to Pinpoint Test G
HCM
B14D9:01
Left Headlamp Light Distribution Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B14D9:64
Left Headlamp Light Distribution Actuator: Signal Plausibility Failure
GO to Pinpoint Test I
HCM
B14D9:87
Left Headlamp Light Distribution Actuator: Missing Message
GO to Pinpoint Test F
HCM
B14D9:87
Left Headlamp Light Distribution Actuator: Missing Message
GO to Pinpoint Test G
HCM
B14DA:01
Right Headlamp Light Distribution Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B14DA:64
Right Headlamp Light Distribution Actuator: Signal Plausibility Failure
GO to Pinpoint Test I
HCM
B14DA:87
Right Headlamp Light Distribution Actuator: Missing Message
GO to Pinpoint Test F
HCM
B14DA:87
Right Headlamp Light Distribution Actuator: Missing Message
GO to Pinpoint Test G
HCM
B14DB:01
Left Headlamp Driver Control System: General Electrical Failure
GO to Pinpoint Test I
HCM
B14DB:54
Left Headlamp Driver Control System: Missing Calibration
GO to Pinpoint Test I
HCM
B14DB:55
Left Headlamp Driver Control System: Not Configured
GO to Pinpoint Test I
HCM
B14DB:87
Left Headlamp Driver Control System: Missing Message
GO to Pinpoint Test F
HCM
B14DB:87
Left Headlamp Driver Control System: Missing Message
GO to Pinpoint Test G
HCM
B14DC:01
Right Headlamp Driver Control System: General Electrical Failure
GO to Pinpoint Test I
HCM
B14DC:54
Right Headlamp Driver Control System: Missing Calibration
GO to Pinpoint Test I
HCM
B14DC:55
Right Headlamp Driver Control System: Not Configured
GO to Pinpoint Test I
HCM
B14DC:87
Right Headlamp Driver Control System: Missing Message
GO to Pinpoint Test F
HCM
B14DC:87
Right Headlamp Driver Control System: Missing Message
GO to Pinpoint Test G
HCM
B1559:96
Left Headlamp: Component Internal Failure
GO to Pinpoint Test I
HCM
B155A:96
Right Headlamp: Component Internal Failure
GO to Pinpoint Test I
HCM
B15A6:01
Right Matrix Controller Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B15A6:87
Right Matrix Controller Actuator: Missing Message
GO to Pinpoint Test F
HCM
B15A6:87
Right Matrix Controller Actuator: Missing Message
GO to Pinpoint Test G
HCM
B15A7:01
Left Matrix Controller Actuator: General Electrical Failure
GO to Pinpoint Test I
HCM
B15A7:87
Left Matrix Controller Actuator: Missing Message
GO to Pinpoint Test F
HCM
B15A7:87
Left Matrix Controller Actuator: Missing Message
GO to Pinpoint Test G
HCM
B1A59:1C
Sensor 5 Volt Supply: Circuit Voltage Out of Range
GO to Pinpoint Test H
HCM
B1D64:01
Left Headlamp Swiveling Motor: General Electrical Failure
GO to Pinpoint Test I
HCM
B1D64:87
Left Headlamp Swiveling Motor: Missing Message
GO to Pinpoint Test F
HCM
B1D64:87
Left Headlamp Swiveling Motor: Missing Message
GO to Pinpoint Test G
HCM
B1D65:01
Right Headlamp Swiveling Motor: General Electrical Failure
GO to Pinpoint Test I
HCM
B1D65:87
Right Headlamp Swiveling Motor: Missing Message
GO to Pinpoint Test F
HCM
B1D65:87
Right Headlamp Swiveling Motor: Missing Message
GO to Pinpoint Test G
HCM
B1D68:64
Left Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure
GO to Pinpoint Test I
HCM
B1D69:64
Right Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure
GO to Pinpoint Test I
HCM
C1A03:12
Left Front Height Sensor: Circuit Short To Battery
GO to Pinpoint Test H
HCM
C1A03:14
Left Front Height Sensor: Circuit Short To Ground or Open
GO to Pinpoint Test H
HCM
C1A03:29
Left Front Height Sensor: Signal Invalid
GO to Pinpoint Test H
HCM
C1A03:64
Left Front Height Sensor: Signal Plausibility Failure
GO to Pinpoint Test H
HCM
C1A05:12
Left Rear Height Sensor: Circuit Short To Battery
GO to Pinpoint Test H
HCM
C1A05:14
Left Rear Height Sensor: Circuit Short To Ground or Open
GO to Pinpoint Test H
HCM
C1A05:29
Left Rear Height Sensor: Signal Invalid
GO to Pinpoint Test H
HCM
C1A05:64
Left Rear Height Sensor: Signal Plausibility Failure
GO to Pinpoint Test H
HCM
U0121:00
Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information
GO to Pinpoint Test J
HCM
U0146:00
Lost Communication With Serial Data Gateway "A": No Sub Type Information
GO to Pinpoint Test K
HCM
U0151:00
Lost Communication With Restraints Control Module: No Sub Type Information
GO to Pinpoint Test M
HCM
U0212:00
Lost Communication With Steering Column Control Module: No Sub Type Information
GO to Pinpoint Test L
HCM
U023A:00
Lost Communication With Image Processing Module A: No Sub Type Information
GO to Pinpoint Test N
HCM
U0415:00
Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information
GO to Pinpoint Test P
HCM
U0429:00
Invalid Data received from Steering Column Control Module: No Sub Type Information
GO to Pinpoint Test P
HCM
U0447:00
Invalid Data Received From Serial Data Gateway "A": No Sub Type Information
GO to Pinpoint Test P
HCM
U0452:00
Invalid Data Received From Restraints Control Module: No Sub Type Information
GO to Pinpoint Test P
HCM
U053B:00
Invalid Data Received From Image Processing Module A: No Sub Type Information
GO to Pinpoint Test P
HCM
U2024:51
Control Module Cal-Config Data: Not Programmed
GO to Pinpoint Test O
HCM
U2024:57
Control Module Cal-Config Data: Invalid / Incompatible Software Component
GO to Pinpoint Test O
HCM
U2100:00
Initial Configuration Not Complete: No Sub Type Information
GO to Pinpoint Test O
HCM
U2101:00
Control Module Configuration Incompatible: No Sub Type Information
GO to Pinpoint Test O
HCM
U2101:56
Control Module Configuration Incompatible: Invalid / Incompatible Configuration
GO to Pinpoint Test O
HCM
U2101:86
Control Module Configuration Incompatible: Signal Invalid
GO to Pinpoint Test O
HCM
U2200:45
Control Module Configuration Memory Corrupt: Program Memory Failure
GO to Pinpoint Test O
HCM
U3000:45
Control Module: Program Memory Failure
GO to Pinpoint Test O
HCM
U3000:46
Control Module: Calibration / Parameter Memory Failure
GO to Pinpoint Test O
HCM
U3003:16
Battery Voltage: Circuit Voltage Below Threshold
GO to Pinpoint Test Q
HCM
U3003:17
Battery Voltage: Circuit Voltage Above Threshold
GO to Pinpoint Test R
SCCM
B124C:96
Turn Indicator Stalk Switch Pack: Component Internal Failure
GO to Pinpoint Test E
SCCM
B124C:9E
Turn Indicator Stalk Switch Pack: Stuck On
GO to Pinpoint Test E
Symptom Chart
Symptom Chart: Headlamps
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...
Removal
NOTICE:
Suspension fasteners are critical parts that affect the
performance of vital components and systems. Failure of these fasteners
may result in major service expense. Use the same or equivalent parts if
replacement is necessary. Do not use a replacement part of lesser
quality or substitute design...